背景信息
Kubenetes支持Pod直接使用主机/节点的网络,对于需要直接访问主机网络的场景有一定的用途。
配置说明
Pod使用主机网络只需要在配置中添加hostNetwork: true即可,如下所示。
apiVersion: apps/v1
kind: Deployment
metadata:
name: nginx
spec:
replicas: 1
selector:
matchLabels:
app: nginx
template:
metadata:
labels:
app: nginx
spec:
hostNetwork: true
containers:
- image: nginx:alpine
name: nginx
imagePullSecrets:
- name: default-secret
部署后可以看到Pod的IP与节点的IP相同,说明Pod直接使用了主机网络。
$ kubectl get pod -owide
NAME READY STATUS RESTARTS AGE IP NODE NOMINATED NODE READINESS GATES
nginx-6fdf99c8b-6wwft 1/1 Running 0 3m41s 10.1.0.55 10.1.0.55 <none> <none>
hostNetwork使用注意事项
Pod直接使用主机的网络会占用宿主机的端口,Pod的IP就是宿主机的IP,使用时需要考虑是否与主机上的端口冲突,因此一般情况下除非您知道需要某个特定应用占用宿主机上的特定端口时,不建议使用主机网络。
由于使用主机网络,访问Pod就是访问节点,要 注意放通节点安全组端口 ,否则会出现访问不通的情况。
另外由于占用主机端口,使用Deployment部署hostNetwork类型Pod时,要注意 Pod的副本数不要超过节点数量 ,否则会导致一个节点上调度了多个Pod,Pod启动时端口冲突无法创建。例如上面例子中的nginx,如果服务数为2,并部署在只有1个节点的集群上,就会有一个Pod无法创建,查询Pod日志会发现是由于端口占用导致nginx无法启动。
注意请避免在同一个节点上调度多个使用主机网络的Pod,否则在创建ClusterIP类型的Service访问Pod时,会出现访问ClusterIP不通的情况。
$ kubectl get deploy
NAME READY UP-TO-DATE AVAILABLE AGE
nginx 1/2 2 1 67m
$ kubectl get pod
NAME READY STATUS RESTARTS AGE
nginx-6fdf99c8b-6wwft 1/1 Running 0 67m
nginx-6fdf99c8b-rglm7 0/1 CrashLoopBackOff 13 44m
$ kubectl logs nginx-6fdf99c8b-rglm7
/docker-entrypoint.sh: /docker-entrypoint.d/ is not empty, will attempt to perform configuration
/docker-entrypoint.sh: Looking for shell scripts in /docker-entrypoint.d/
/docker-entrypoint.sh: Launching /docker-entrypoint.d/10-listen-on-ipv6-by-default.sh
10-listen-on-ipv6-by-default.sh: info: Getting the checksum of /etc/nginx/conf.d/default.conf
10-listen-on-ipv6-by-default.sh: info: Enabled listen on IPv6 in /etc/nginx/conf.d/default.conf
/docker-entrypoint.sh: Launching /docker-entrypoint.d/20-envsubst-on-templates.sh
/docker-entrypoint.sh: Launching /docker-entrypoint.d/30-tune-worker-processes.sh
/docker-entrypoint.sh: Configuration complete; ready for start up
2022/05/11 07:18:11 [emerg] 1#1: bind() to 0.0.0.0:80 failed (98: Address in use)
nginx: [emerg] bind() to 0.0.0.0:80 failed (98: Address in use)
2022/05/11 07:18:11 [emerg] 1#1: bind() to [::]:80 failed (98: Address in use)
nginx: [emerg] bind() to [::]:80 failed (98: Address in use)
2022/05/11 07:18:11 [emerg] 1#1: bind() to 0.0.0.0:80 failed (98: Address in use)
nginx: [emerg] bind() to 0.0.0.0:80 failed (98: Address in use)
2022/05/11 07:18:11 [emerg] 1#1: bind() to [::]:80 failed (98: Address in use)
nginx: [emerg] bind() to [::]:80 failed (98: Address in use)
2022/05/11 07:18:11 [emerg] 1#1: bind() to 0.0.0.0:80 failed (98: Address in use)
nginx: [emerg] bind() to 0.0.0.0:80 failed (98: Address in use)
2022/05/11 07:18:11 [emerg] 1#1: bind() to [::]:80 failed (98: Address in use)
nginx: [emerg] bind() to [::]:80 failed (98: Address in use)
2022/05/11 07:18:11 [emerg] 1#1: bind() to 0.0.0.0:80 failed (98: Address in use)
nginx: [emerg] bind() to 0.0.0.0:80 failed (98: Address in use)
2022/05/11 07:18:11 [emerg] 1#1: bind() to [::]:80 failed (98: Address in use)
nginx: [emerg] bind() to [::]:80 failed (98: Address in use)
2022/05/11 07:18:11 [emerg] 1#1: bind() to 0.0.0.0:80 failed (98: Address in use)
nginx: [emerg] bind() to 0.0.0.0:80 failed (98: Address in use)
2022/05/11 07:18:11 [emerg] 1#1: bind() to [::]:80 failed (98: Address in use)
nginx: [emerg] bind() to [::]:80 failed (98: Address in use)
2022/05/11 07:18:11 [emerg] 1#1: still could not bind()
nginx: [emerg] still could not bind()